- 您现在的位置：买卖IC网 > Sheet目录868 > LTM4628EV#PBF (Linear Technology)IC DC/DC UMODULE 16A 144-LGA
LTM4628
PIN FUNCTIONS
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
TRACK1, TRACK2 (E5, D8): Output Voltage Tracking Pin
and Soft-Start Inputs. Each channel has a 1.3μA pull-up
current source. When one channel is configured to be
master of the two channels, then a capacitor from this pin
to ground will set a soft-start ramp rate. The remaining
channel can be set up as the slave, and have the master’s
output applied through a voltage divider to the slave out-
put’s track pin. This voltage divider is equal to the slave
output’s feedback divider for coincidental tracking. See
the Applications Information section.
COMP1, COMP2 (E6, E7): Current control threshold and
error amplifier compensation point for each channel. The
current comparator threshold increases with this control
voltage. Tie the COMP pins together for parallel operation.
The device is internal compensated.
DIFFP (E8): Positive input of the remote sense amplifier.
This pin is connected to the remote sense point of the output
voltage. Use of the remote sense amplifier is limited to an
output voltage between 0.6V and 3.3V inclusive. Connect to
GND if not used. See the Applications Information section.
DIFFN (E9): Negative input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output GND. See the Applications Information section.
MODE_PLLIN (F4): Force Continuous Mode, Burst Mode
Operation, or Pulse-Skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to SGND to force both channels into
force continuous mode of operation. Connect to INTV CC
to enable pulse-skipping mode of operation. Leaving the
pin floating will enable Burst Mode operation. A clock on
the pin will force both channels into continuous mode of
operation and synchronized to the external clock applied
to this pin.
RUN1, RUN2 (F5, F9): Run Control Pin. A voltage above
1.25V will turn on each channel in the module. A voltage
below 1.25V on the RUN pin will turn off the related chan-
nel. Each RUN pin has a 1μA pull-up current, once the
RUN pin reaches 1.2V an additional 4.5μA pull-up current
is added to this pin.
DIFFOUT (F8): Internal Remote Sense Amplifier Output.
Connect this pin to V OUTS1 or V OUTS2 depending on which
output is using remote sense. In parallel operation con-
nect one of the V OUTS pin to DIFFOUT for remote sensing.
Leave floating if the remote sense amplifier is not used.
SW1, SW2 (G2, G11): Switching node of each channel
that is used for testing purposes. Also an R-C snubber
network can be applied to reduce or eliminate switch node
ringing, otherwise leave floating. See the Applications
Information section.
PHASMD (G4): Connect this pin to SGND, INTV CC , or float-
ing this pin to select the phase of CLKOUT to 60 degrees,
120 degrees, and 90 degrees respectively.
CLKOUT (G5): Clock output with phase control using the
PHASMD pin to enable multiphase operation between
devices. See the Applications Information section.
PGOOD1, PGOOD2 (G9, G8): Output Voltage Power
Good Indicator. Open drain logic output that is pulled to
ground when the output voltage is not within ±7.5% of
the regulation point.
INTV CC (H8): Internal 5V Regulator Output. The control
circuits and internal gate drivers are powered from this
voltage. INTV CC is controlled and enabled when RUN1 or
RUN2 is activated high. Decouple this pin to PGND with
a 4.7μF low ESR tantalum or ceramic.
TEMP (J6): Onboard Temperature Diode for Monitoring
the VBE Junction Voltage Change with Temperature. See
the Applications Information section.
EXTV CC (J7): External power input that is enabled through
a switch to INTV CC whenever EXTV CC is greater than 4.7V.
Do not exceed 6V on this input, and connect this pin to
V IN when operating V IN on 5V. An efficiency increase will
occur that is a function of the (V IN – INTV CC ) multiplied by
power MOSFET driver current. Typical current requirement
is 30mA. V IN must be applied before EXTV CC , and EXTV CC
must be removed before V IN .
V IN (M2-M11, L2-L11, J2-J4, J9-J11, K2-K4, K9-K11):
Power Input Pins. Apply input voltage between these pins
and GND pins. Recommend placing input decoupling
capacitance directly between V IN pins and GND pins.
4628fe
8
For more information www.linear.com/LTM4628
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTM8008HV#PBF
IC DC/DC UMODULE 16-LGA
LTM8020IV#PBF
IC DC/DC UMODULE 200MA 21-LGA
LTM8023MPV#PBF
IC BUCK SYNC ADJ 2A 50LGA
LTM8025MPV#PBF
IC CONVERTER BUCK 3A ADJ 70LGA
LTM8026MPV#PBF
IC UMODULE 36VIN 5A CVCC 81LGA
LTM8027EV#PBF
IC BUCK SYNC ADJ 4A 113LGA
LTM8032MPY#PBF
IC DC/DC UMODULE 2A 71BGA
LTM8033MPV#PBF
IC DC-DC UMODULE BUCK 3A 76-LGA
相关代理商/技术参数
LTM4628EVPBF
制造商:Linear Technology 功能描述:DC/DC Regulator Dual 8A or Single 16A
LTM4628IV#PBF
功能描述:IC DC/DC UMODULE 16A 144-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM4628IVPBF
制造商:LINEAR_DIMENSIONS 制造商全称:LINEAR_DIMENSIONS 功能描述:Dual 8A or Single 16A DC/DC ??Module Regulator
LTM4628IY#PBF
制造商:Linear Technology 功能描述:IC DC/DC UMODULE 16A 144-BGA 制造商:Linear Technology 功能描述:DP-uModule, Dual 8A or Single 16A DC/DC uModule Regulator
LTM4630EV#PBF
制造商:Linear Technology 功能描述:DC/DC CONVERTER DUAL 0.6-1.8 65W 制造商:Linear Technology 功能描述:BUCK UMODULE 15VIN 18A LGA 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, LGA-144, Primary Input Voltage:15V, No. of Outputs:2 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, LGA-144, Primary Input Voltage:15V, No. of Outputs:2, Output Current:36A, No. of Pins:144, Operating Temperature Min:-40C, Operating Temperature Max:125C, MSL:MSL 3 - 168 hours, Package / Case:144-LGA , RoHS Compliant: Yes
LTM4630IV#PBF
制造商:Linear Technology 功能描述:DC/DC CONVERTER DUAL 0.6-1.8 65W 制造商:Linear Technology 功能描述:BUCK UMODULE 15VIN 18A LGA 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, LGA-144, Primary Input Voltage:15V, No. of Outputs:2, Output Current:36A, No. of Pins:144, Operating Temperature Min:-40C, Operating Temperature Max:125C, MSL:MSL 3 - 168 hours, Package / Case:144-LGA , RoHS Compliant: Yes
LTM4633EY#PBF
制造商:Linear Technology 功能描述:DC/DC CNVRTR 2X0.8-1.8V 0.8-5.5V 制造商:Linear Technology 功能描述:IC, DC/DC SMPS, 750KHZ, BGA-144 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK, ADJ, 750KHZ, BGA-144, Primary Input Voltage:16V, No. of Outputs:3, Output Current:10A, No. of Pins:144, Operating Temperature Min:-40C, Operating Temperature Max:125C, Package / Case:144-BGA , RoHS Compliant: Yes
LTM4633MPY#PBF
制造商:Linear Technology 功能描述:IC, DC/DC SMPS, 750KHZ, BGA-144